SHAFTSTIK® Golf Club Rapid Shafting Glue – Two Part Adhesive

SHAFTSTIK® ‘DON’T LOSE YOUR HEAD SHAFTING GLUE’ exclusively available to the every club maker and golf workshop and enthusiast across Europe.

SHAFTSTIK® ‘DON’T LOSE YOUR HEAD SHAFTING GLUE’ is a two-part fast-setting ‘high impact’ toughened’ adhesive developed specifically for use with a wide variety of substrates such as steel golf club shafts, graphite golf shafts and other materials associated with golf club components.

Professional’s and Custom-Fit Workshops use this every day for building golf clubs. It has been tried, tested, and improved over many years and has sold over 1m+ units worldwide. The formula makes this one of the best solutions for golf club shafting available.

It cures rapidly at room temperature within 5 minutes and gives a handling strength in approximately 8 minutes, allowing you to handle the club with confidence after a short period of time.

30-60 minutes gives you an ideal working time, allowing you to work on the golf club as required, such as re-gripping, painting and making loft and lie adjustments without sacrificing valuable workshop time or overall strength of the bond.

24 hours gives you a full cure and the strongest ‘high impact’ and truly ‘toughened’ golf club shafting glue, that is highly recommended for golf club re-shafting.

(Faster full curing shafting glue is not recommended by most Professionals club makers and epoxy resin engineers due to the nature and stress involved when hitting golf balls, the longer the full curing time the stronger the bond).

‘So don’t lose your head’ and use SHAFTSTIK with the upmost confidence!    

Typical Curing Properties

Mix ratio by volume 1:1

Maximum gap fill 2 mm

Usable / pot life @23°C 3-4 mins

Handling time @23°C 5-8 mins

Working strength @23°C 30-60 mins

Full cure @23°C 24 hours

Dries Clear

An increase of 8°C in temperature will halve the cure time. Lower temperatures will result in a slower cure time.

Golf Club Preparation: Surfaces/Hosels/Shafts should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces if required. Most shafts/hosels and surfaces will benefit from light abrasion with emery cloth (or similar), to remove any oxide layer and provide a better bond.

Directions for Use: 1. Dual cartridges: Remove the cartridge cap and dispense epoxy until both sides are flowing. 2. Mix equal amounts. 3. Apply the epoxy to one or both components. 4. Join the parts and apply a firm pressure, secure components if possible. 5. Parts must be joined within 3-4 minutes of mixing the two epoxy components. 6.  Large quantities and/or higher temperature will decrease the usable mix time life.  7. Full cure will be obtained after 24 hours at 25°C (77°F). Heat can be used to accelerate the curing process but always remember the saying in club making ‘longer is stronger’.

Safety Guidelines:

Use in accordance with the safety data sheet (provided on request) and/or the guidelines as per the label/s on the product. For further assistance with this product call our helpline on +44 (1952 743 038).

Shelf life and Storage Store in a cool dry place in an air tight container and replace cap straight after use, always keep upright when storing. Follow all the guidelines within the safety data sheet (available on request). If stored correctly this product has a shelf life for a period of 6 months.

About:

The development, manufacturing and engineering of the adhesives, glues, and epoxy resins used spans four decades and three continents, of which is backed up by a high-tech ISO certified production plant and high-grade manufacturing and research and development facility, with expertise of the highest level.

Be sure to check out our ‘SHAFTSTIK Black Super Glue’, the ultimate solution for those that require a super glue that bonds in seconds.golf club ferrules to your club head.